Dadri U-1 functional Loocation /Job Card Help

 

Functional loc. 1011-S1U01 Valid From 20.08.17
Description STAGE-1 UNIT-1

HP Bypass . LP Bypass Operation

Dadri stage-1 Reserve Shut down Procedure

 PROCEDURE FOR RESERVE SHUT DOWN OF STAGE-1 UNITS

PREPARATIONS

Dadri stage-1 : ST-1, ST-2 Both tripping

 In case of both station transformer tripping following disturbance will be observed

SOP for Mills Operation along with Bio Mass

 1) Mill Operating Parameters and Operation procedure:

Work Instructions

Start-Up After 8 Hours of Shutdown ( Hot start-UP)

Unit condition

1	At least 2 BCW pump in Serrvice
2	Both SAPH and PAPH Running
3	Turbine : On Barring (AOP,JOP,SOP, HPCF in service)
4	Generator: PW system, Seal Oil system, Gas system

SCED Features

SCED Features

• NLDC has opened a separate bank account called ‘National Pool Account (SCED)’. All payments to/from the generators and to the Discoms on account of SCED flow to/from the said National Pool Account (SCED)

Power Terminology

Power Terminology

• 100MW for 24 Hrs = 2.4 MU (Million Units)
• Ancillary services refer to functions that help grid operators maintain a reliable electricity system.
• Ancillary services maintain the proper flow and direction of electricity, address imbalances between supply and demand, and help the system recover after a power system event

RH Metal Temp Optimization

RH Metal Temp Optimization

• Causes of Rh Tube Fail:  

(a) COAL ASH CORROSION FOR TUBING
(b) UNEVEN TEMPERATURE DISTRIBUTION ACROSS THE BOILER

Dry Ash system : 500 MW

Dry Ash system : 500 MW

• Ash is oxidised form of the mineral matters present in coal
• Typical ash composition : SiO2, Al2O3, Fe2O3, CaO, MgO etc
• Coal with more SiO2 & Al2O3, Ash MP > 1400ºC

Shut-Down Procedure: 500 MW (Planned Shutdown)

Shut-Down Procedure: 500 MW

• Reduce load from 500 MW to 400 MW
• Gradualy Reduce Pr SP from 170 ksc to 130 ksc, Load is still 400 MW
• Take unit of TFM

New Regulation: Real Time Market Power Trading

Hydrogen Purging

Pre-Purging checklist:

1. The generator may be on barring gear or at standstill. Preferably be on barring speed of around 50-80rpm (without condenser vacuum).
 At least 60 CO2 filled cylinders should be available in the unit where purging is to be done.
 Arrangement for filling hot water on CO2 cylinder / lines (to avoid freezing) is to be ready.

Loss of Instrument Air

Loss of Instrument Air
Anticipated Problems:

1. No oil burner can be taken in service. Oil guns, oil/steam valves will remain inoperative.
The igniter will not get advance.

Vacuum Pulling Process

Vacuum Pulling Process
1 Ensure permit cancellation on Vacuum pump/Flash Tank related MOV/Condensate system & Clearance for vacuum pulling.

Mill Fire

Mill Fire
a) Fire in mill under shut down:
 Isolate the mill totally from air side by closing cold/hot air dampers & gates and mill seal air valves.

Shutdown Instructions

Shutdown Instructions
1 Ensure UT change over before tripping of boiler/ turbine.
2 Ensure 400 KV breaker are opened after unit tripping.

UPS Failure

UPS Failure

CONSEQUENCES OF 240 VOLT UPS SUPPLY FAILURE:-

 All LVS supplies from main UPS will not be available but from mini UPS supply will be
available for around 2 hours .

Boiler forced Cooling

Boiler Forced Cooling

1 In case of Tube leakage

1.1 After Tripping the boiler ,stop FD fan and keep ID fan running at
minimum load and ensure furnace pressure negative inside boiler.

CC(BCW) Pump Isolation & Purging

CC(BCW) Pump Isolation & Purging

1. ISOLATION OF CC PUMP REMARKS

1.1 Remove from Stand by mode if it is in auto
1.2 Stop CC pump if running

Bunker fire : Prevention

Bunker fire

PREVENTION OF BUNKER FIRE

 Ensure Feeder outlet gate closes on auto when Feeder stopped/tripped. Otherwise give
a close command for closing.

ACW pump house

Condenser : One Pass Isolation

1 Ensure the availability of both condenser de-watering pumps.
2 Decrease the load to 300 – 350 MW
3 Ensure that both CW interconnection valve are opened
4 Start Stand by Vacuum pump

Generator Air tightness Test

TEST PROCEDURE: -
1) Air Filling valve is to be opened for flushing of line & removal of moisture in atmosphere.
2) Chemistry is to take sample for dew point measurement. After chemistry clearance , Filling process
has to be continued.
3) Close the waste gas (vent) valves.

APH Hot Washing

1 Water washing of air heaters should be carried out in hot condition after boiler shutdown.Flue gas inlet temperature should be between 200 deg C to 150 deg C
2 Both FD/ID/PA fans should be in stopped condition
3 All APH flue gas outlet damper should be closed

Stopping one FD Fan

1 Reduce the load to 400 MW & then remove from CMC
2 Before Unloading FD Fan (to be stopped ),The following
Permissive & Protection to be kept bypassed :
“FD Fan ON & Discharge Gate close” permissive to be given
“FD Fan ON & Discharge gate auto open” to be bypassed.

Stopping one PA Fan

1 Reduce the load to 300 MW & then remove from CMC
2 Keep 4 consecutive Mills in service. If required , take oil guns in service

Stopping one ID Fan

1. Reduce Load to 300MW
2. Start Unloading corresponding FD fan & increase loading of other FD Fan through blade pitch.

Stopping one PAPH

• Reduce Load to 300MW
• Slowly close flue gas outlet damper for PAPH which has to be stopped

Stopping one SAPH

• Reduce Load to 300MW
• Slowly close flue gas outlet damper (2 in no. )for APH which has to be stopped
• Adjust other PAPH/SAPH flue gas outlet damper
• Close flue gas inlet damper
• Close SCAPH inlet , outlet & bypass damper. During Closing , Observe Air Flow.
• Close SAPH air outlet damper (2 in no.)
• Stop the SAPH motor once flue gas inlet temperature reduced below 150deg C
• Close Air motor main isolating valve & bypass isolating valve

LIGHT UP CHECK POINTS

BEFORE LIGHT UP ACTIVITIES

BOILER SIDE

• MAN ,MATERIAL REMOVED AND BOILER IS READY FOR LIGHT UP.
  

Water-chemistry: 500 MW

Recommended Parameter Values
1. Boiler Water – pH = 9.1-9.4
2. Boiler Water – Specific Conductivity < 20.0 μs/cm
3. Boiler Water – Silica < 100 ppb
4. Boiler Water - Phosphate = 1-2 ppm
5. Boiler Water - Chloride < 0.5 ppm

Check List (Light-Up)

Unit:

Date:

Switchyard Breaker arrangement: Rihand

Stage-I

GT#1  à 1-52  Main (GCB to Bus Bar-1) à 2-52 (Tie-GCB to bus Bar-2) à 3-52(IBT-1 i/c)

GT#2 à 7-52Main (GCB to Bus Bar-2) à 8-52((Tie-GCB to bus Bar-1)

Bus bar-1 à 4-52 (H1) à 5-52(Tie H1-S2) à 6-52(S2) à Bus Bar-2

Bus bar-2 à 10-52 (S1) à 11-52(Tie S1-H2) à 12-52(H2) à Bus Bar-1

Bus-1  ß13-52(Bus-coupler-1) à Bus-3

Bus-2  ß14-52(Bus-coupler-2) à Bus-4

Turbine Governing system

Key Points

Ø  Governing- Regulation of Turbine Speed under No Load and Varying Load

Ø  Others Works: CV Actuation/ Initial Run-up & Synchronization/ Load Variation to meet Grid Freq

Ø  500 MW KWU: Throttle Governed Machine

Ø  2 Governors , EHC and HG connected in Parallel: Only One at a time through Hyd Minimum slection

Ø  CVs Open according to Secondary oil Pressure

Ø  Between 100 MW  to 525 MW , Load variation done by HPCV throttling

Important Procedures

Vacuum Pulling : Procedure:

Ø  Close RH Vents, CRH, HRH UFT drains

Ø  Close Vacuum Breaker

Ø  Open 8.5 m steam Manual valve full Both (100%), Temp> 250 Deg ( Open

Ø  Start GSC Exhauster Fan

Ø  Start Both Vacuum pumps ( Casing Empty, Receiver tank Level adeq)

Ø  At -0.2 ksc charge steam gradually ( lower Controller from 50% à 0 %)

Ø  Build Vacuum upto -0.9 ksc

Hydrogen Purging

Ø  SLC AS SOP Off, SLC DC SOP Off, SLC H2 SOP Off

Ø  Suppy of DC SOP Off

Ø  Start one AC SOP ( DP=1.5 ksc)

Ø  Dew Point Air=<-10 Deg, clearance from Chemist

Ø  H2 (Isolated Position), CO2(Isolated Position), Air Inlet(Open), Casing vent ( Closed)

Ø  Fill and Pressurise upto 0.5 ksc

Cold start-up

Points to Remember

Ø  maximum of HP casing and HP shaft is less than 150°C(more than 5 days)

Ø  It requires soaking of Turbine at 360 rpm with steam(40ksc,360 Deg)

Ø  An upper limit of 200° C/hr. saturation temp gradients can be allowed, i.e. approximately the boiler pressure can be brought to 20 Kg/ Cm² within an hour of cold start up

Ø  But actual temp gradient is limited by the thick walled Y piece provided in the main steam and HRH lines

Ø  maximum differential temp allowed between inner (98%) and mid wall temp (50%) is ±40°C

Ø  Start only two CC pumps in order to minimize flashing in down comers (and subsequent vibration) when the boiler water is in the range of 85° to 125° C

IBT Outage

Consequences on Stage-2 ( Station Transformer Tripped)

Ø  132 KV Switchyard dead results in tripping of -Station Transformers, Construction Transformer, Misc Transformer

Ø  All colony power( Lighting,Water supply) will get interrupted

Ø  Power Supply to DM Plant, HFO Pump house, PTCW Pump house, Offsite Board, ADPH,

Ø  Following Board will get dead:

§  OBA,OBB,OBC,OBD (11 KV station Board)

§  OCA,OCB (3.3 KV Station aux Board), ADPH MCC, CHP Transformers

§  DMPT, CWST, WTPT,BTST,ODA,ODB(Station Service), ODC(FW Pump House),ODD ( Offsite ): 3.3 KV

§  OQA,OQB(St. Serv),3SA,4SA(Air Washer MCC),3TA,4TA(Unit Ventilation MCC),OTA(HVAC ) : 415 V

§  OSA(SW MCC), OTB(Serv Bldg Ventilation MCC), FOPH : 415 V

Main Equipments Tripped

Instrument Air supply Failure

Reasons of  Failure:

Ø  Failure of control supply of  compressor

Ø  Loss of Cooling Water (SG ECW Pump Trip)

Ø  Massive leakage in  IA supply Header

Ø  One Unit Under Overhaul. Unit Aux Board/ Station Aux board  got Tripped of that Unit

Ø  Total Black Out of any stage

DG Load Trial and Regular checks

Requirements:

1	Inform & Ensure availability of TMD/EMD/C&I
2	SG/TG/BOP source-2 AC Power Supply Interruption. Inform C&I for Standby chargers
3	Ensure DG Set Tank Oil Level Adequate
4	Evacuate and Isolate Boiler Passenger, Service Building Lift and Isolate. Inform EMD(temporary supply )
5	Arrange 3 Walky Talky : 1-CR 2-DG board 3-DG Set room
6	Note Down Initial Parameters of DG Set

Furnace Air Tightness Test

Ø  Scope- Boiler Furnace, Air and FG Duct upto ID Fan Inlet

Ø  Why- To test Tightness of Furnace wrt Environment not for Strength

Ø  Ensure- All PTWs of BMD( PP, Rotary, Mills, Ash handling) cancelled and Clearance Available

Emergency Instructions:220 V DC Failure

220 V DC Failure

Unit condition

Ø  DCDB section-1 & 2 under voltage alarm in LVS-5

Ø  All HT/LT Breakers Indication Becomes Bad

Ø  Boiler will Trip on MFT ( after 2 Sec)

Ø  Turbine will Trip on MFT

Ø  Generator will not Trip as GCB Protection will not act

Ø  Generator will run as Synchronous Motor

Start-Up After 8 Hours of Shutdown ( Hot start-UP)

Unit condition

1	At least 2 BCW pump in Serrvice
2	Both SAPH and PAPH Running
3	Turbine : On Barring (AOP,JOP,SOP, HPCF  in service)
4	Generator: PW system, Seal Oil system, Gas system
5	Condenser Pass : Both Charged
6	PAC & IAC : 1 PAC & 2 IAC in Service
7	CEP & Make-up :  1 CEP with H/W Make-up on auto

Tripping on Boiler Tube Leakage

Mill reject system

CERC Norms 2019 Vs 2014 : Changes

TDBFP Rolling