DG Load Trial and Regular checks



Requirements:
1
Inform & Ensure availability of TMD/EMD/C&I

2
SG/TG/BOP source-2 AC Power Supply Interruption. Inform C&I for Standby chargers

3
Ensure DG Set Tank Oil Level Adequate

4
Evacuate and Isolate Boiler Passenger, Service Building Lift and Isolate. Inform EMD(temporary supply )

5
Arrange 3 Walky Talky : 1-CR 2-DG board 3-DG Set room

6
Note Down Initial Parameters of DG Set


Status of Unit:
1
TG on Barring

2
Generator Depressurized(H2/CO2 Purged out)

3
Seal Oil system in Service

4
All Drives in DG Bus in available condition( Plan within 1-2 days of Unit shut down)

5
DG Board charged from Normal Incomer Breaker from Unit Service Board


Sequence:
Ø  Start all drives on DG Bus from other standby source(other board)
Ex- SOP-2 to Sop-1, FD/ID/PA Lop-2 to LOP-1
Ø  Start Main DG set & Note Down: Volatge, RPM, Tank Level, LO Pr/Temp, Battery Voltage
Ø  Trip Normal Incomer from USS and Close DG set Incoming breaker to charge DG Bus
Ø  Start Loading Drives by starting them which are on DG Bus
Ø  Continue Test run fro ½ -1 Hour.
Normalisation:
Ø  Start all drives on DG Bus from other standby source(other board)
Ø  Trip DG Set Incoming Breaker  and Close Normal Incomer From USS
Ø  Switch Off DG Set
Regular checks:
Ø  DG Set Fuel Tank Level Normal
Ø  DG Set engine Oil Level Normal
Ø  Battery charger OK
Ø  Engine Coolant level is OK
Ø  DG Set Incomers to DG Bus Healthy

Comments

Post a Comment

Popular posts from this blog

HP & LP Bypass Operation and Protection

Image
HP & LP Bypass Operation and Protection Purpose Boiler operation independent of the turbine Minimum steam flow through SH & RH tubes during start-ups, low load operation & sudden unloading of unit Utilized or building up of steam parameters Avoiding the boiler trip on Reheat protection No steam flow through Boiler steam tubes will lead to starvation & thereby overheating and lead to premature failure of tubes  The capacity of HPLP bypass is 60% of full load turbine steam flow  Reheat Protection: RH protection (delay=10 sec) will act if TURBINE HP V/V & HPBP CLOSED [ either turbine HP stop v/v or HP CV in both HP line closed ] & [ both HP BP <2%]             OR TURBINE IP V/V & LP BP closed [ Either IP stop v/v or IP CV v/v in both IP line closed ] & [ Either LP BP stop v/v or LP BP C/V in both LP line is closed] OR   Generator ckt bkr open & [both HP BP closed OR both L...
Read more

Generator Air Tightness Test

Generator Air Tightness Test Period Of Test= 24 Hrs without a Break Air Pressure Drop (Allowed in 24 Hrs) : <=0.15 ksc Air Test Pressure = 3.5 ksc All LLDs Drain Closed. Ensure Seal Oil system in Operation Seal Oil DP >1.5 ksc AS Seal Oil Pr>4.5 ksc, start H2S Seal Oil system H2 Cooler Isolated PW in Winding is in filled condition, Winding Isolated. PW also kept Isolated. PW Tank at Atmospheric Pressure Ensure availability of  Instrument air and Bleed Out moisture from it by keeping it open till  Connect flexible air hose with the gas plant through the coupling and ensure no air leakage is there  The filling is to be done by opening the valves in the normal H2 filling line where as the valve from H2 rack side will remain closed. Once the air filling is commenced the test record data sheet   The air valve is to be opened full. While pressurising the LLD / Seal oil DP / Seal oil parameters are to be recorded as per the enclosed sheet. The...
Read more