CHECK LIST FOR AIR INGRESS IN CONDENSER

CHECK LIST FOR AIR INGRESS IN CONDENSER
Sl No
Description
Location
Checked status
1.       
Valve gland sealing water pressure (UCB).
UCB

2.       
Gland steam pressure & temp
UCB

3.       
Vacuum breaker Valve
17 mtr

4.       
HPT / IPT / LPT glands
17 mtr

5.       
TDBFP-A  gland
17 mtr

6.       
TDBFP-B  gland
17 mtr

7.       
LPT Diaphragm
17 mtr

8.       
TDBFP-A  Diaphragm
17 mtr

9.       
TDBFP-B  Diaphragm
17 mtr

10.   
LPT Manholes  ( both side )
17 mtr

11.   
TDBFP-A  exhaust valve
8.5 mtr

12.   
TDBFP-B  exhaust valve
8.5 mtr

13.   
LPH-2/3 vents to condenser
8.5 mtr

14.   
HPHs vents to condenser
8.5 mtr

15.   
LPH-2 shell side vent line valves & flanges
8.5 mtr

16.   
LPH-3 shell side vent line valves & flanges
8.5 mtr

17.   
Vaccum p/p-1/ 2 suction line manual valve glands at condenser
8.5 mtr

18.   
Condenser Man holes (8.5 mtr both sides)
8.5 mtr

19.   
LPH-1 Emergency drip to condenser( LCV-0700)
0 mtr

20.   
LP Header-2 drip line ( LCR-0757B-HD4-022)
0 mtr

21.   
LP Header-3 drip line to condenser
0 mtr

22.   
HPH-5A/5B emergency drip to condenser
0 mtr

23.   
Drainn valves connected to TFT-1/2
0 mtr

24.   
TFT-1/2 header connections
0 mtr

25.   
Condenser level transmitters.
0 mtr

26.   
Condenser level Switches.
0 mtr

27.   
Vaccum pump-1, 2 suction line manual and motorised valve glands and flanges.
0 mtr

28.   
Deaerator  to condenser valve glands (Co-I5I)
0 mtr

29.   
CEP recirculation lines-A, B, C valve glands.&vents and drains
0 mtr

30.   
LPH-1 normal drip top condenser valves.
0 mtr

31.   
CEP – A/B/C glands
(- m  mtr)

32.   
CEP – A/B/C   suction strainers & vents
(- m  mtr)

33.   
CEP – A/B/C suction line drains
(- m  mtr)

34.   
Hotwell drain line passing
(- m  mtr)

35.   
CEP suction and discharge line flanges
(- m  mtr)

36.   



37.   





Comments

Post a Comment

Popular posts from this blog

HP & LP Bypass Operation and Protection

Image
HP & LP Bypass Operation and Protection Purpose Boiler operation independent of the turbine Minimum steam flow through SH & RH tubes during start-ups, low load operation & sudden unloading of unit Utilized or building up of steam parameters Avoiding the boiler trip on Reheat protection No steam flow through Boiler steam tubes will lead to starvation & thereby overheating and lead to premature failure of tubes  The capacity of HPLP bypass is 60% of full load turbine steam flow  Reheat Protection: RH protection (delay=10 sec) will act if TURBINE HP V/V & HPBP CLOSED [ either turbine HP stop v/v or HP CV in both HP line closed ] & [ both HP BP <2%]             OR TURBINE IP V/V & LP BP closed [ Either IP stop v/v or IP CV v/v in both IP line closed ] & [ Either LP BP stop v/v or LP BP C/V in both LP line is closed] OR   Generator ckt bkr open & [both HP BP closed OR both L...
Read more

Generator Air Tightness Test

Generator Air Tightness Test Period Of Test= 24 Hrs without a Break Air Pressure Drop (Allowed in 24 Hrs) : <=0.15 ksc Air Test Pressure = 3.5 ksc All LLDs Drain Closed. Ensure Seal Oil system in Operation Seal Oil DP >1.5 ksc AS Seal Oil Pr>4.5 ksc, start H2S Seal Oil system H2 Cooler Isolated PW in Winding is in filled condition, Winding Isolated. PW also kept Isolated. PW Tank at Atmospheric Pressure Ensure availability of  Instrument air and Bleed Out moisture from it by keeping it open till  Connect flexible air hose with the gas plant through the coupling and ensure no air leakage is there  The filling is to be done by opening the valves in the normal H2 filling line where as the valve from H2 rack side will remain closed. Once the air filling is commenced the test record data sheet   The air valve is to be opened full. While pressurising the LLD / Seal oil DP / Seal oil parameters are to be recorded as per the enclosed sheet. The...
Read more