3.3 KV bus charging

3.3 KV bus charging from bus coupler/ Normal Incomer

 A:    Bus charging from bus coupler: - (Only done from Electrical control panel at UCB)

 1. Select 3.3 KV bus coupler breaker
2. Select I/C-A or I/C-B in trip selection (Select the incomer that we want to trip).
3. Put Key (Synch selection) in position “1 - check “.
4. Switch ON synchroscope by putting switch in position “2”.
5. If IN PHASE lamp (green LED) glows. Go to step-6. If OUT OF PHASE (RED LED) Glows
check for voltage/frequency difference & inform to EMD.
6. Close Circuit breaker (control switch position “2”). Bus coupler breaker will close &
incomer (which selected in trip selection) will trip.
7. Change over completed, Switch OFF synchroscope & put key in “0 – OFF” position.
8. Deselect bus coupler .
9. Reset all by pressing Control reset.

B: Bus charging from normal incomer :- (Only done from Electrical control panel at UCB)

 1. Select 3.3kv Incomer breaker ( incomer-1/ incomer-2)
2. Select Bus coupler in trip selection.
3. Put Key (synch selection) in position “1 - check “.
4. Switch ON synchroscope by putting switch in position “2”.
5. If IN PHASE lamp (green LED) glows. Go to step-6. If OUT OF PHASE (RED LED) Glows
check for voltage/frequency difference & informed to EMD.
6. Close Circuit breaker (control switch position “2”). Incomer will close & Bus coupler
breaker will trip.
7. Change over completed, Switch OFF synchroscope & put key in “0 – OFF” position.
8. Deselect incomer breaker ( incomer-1/incomer-2).

9. Reset all by pressing Control reset.

Comments

Post a Comment

Popular posts from this blog

HP & LP Bypass Operation and Protection

Image
HP & LP Bypass Operation and Protection Purpose Boiler operation independent of the turbine Minimum steam flow through SH & RH tubes during start-ups, low load operation & sudden unloading of unit Utilized or building up of steam parameters Avoiding the boiler trip on Reheat protection No steam flow through Boiler steam tubes will lead to starvation & thereby overheating and lead to premature failure of tubes  The capacity of HPLP bypass is 60% of full load turbine steam flow  Reheat Protection: RH protection (delay=10 sec) will act if TURBINE HP V/V & HPBP CLOSED [ either turbine HP stop v/v or HP CV in both HP line closed ] & [ both HP BP <2%]             OR TURBINE IP V/V & LP BP closed [ Either IP stop v/v or IP CV v/v in both IP line closed ] & [ Either LP BP stop v/v or LP BP C/V in both LP line is closed] OR   Generator ckt bkr open & [both HP BP closed OR both L...
Read more

Generator Air Tightness Test

Generator Air Tightness Test Period Of Test= 24 Hrs without a Break Air Pressure Drop (Allowed in 24 Hrs) : <=0.15 ksc Air Test Pressure = 3.5 ksc All LLDs Drain Closed. Ensure Seal Oil system in Operation Seal Oil DP >1.5 ksc AS Seal Oil Pr>4.5 ksc, start H2S Seal Oil system H2 Cooler Isolated PW in Winding is in filled condition, Winding Isolated. PW also kept Isolated. PW Tank at Atmospheric Pressure Ensure availability of  Instrument air and Bleed Out moisture from it by keeping it open till  Connect flexible air hose with the gas plant through the coupling and ensure no air leakage is there  The filling is to be done by opening the valves in the normal H2 filling line where as the valve from H2 rack side will remain closed. Once the air filling is commenced the test record data sheet   The air valve is to be opened full. While pressurising the LLD / Seal oil DP / Seal oil parameters are to be recorded as per the enclosed sheet. The...
Read more